Megger MFT-X1 Multifunction Installation Tester
Includes: Switched test probe SP5, red test lead, probes, clips and grabbers, blue test lead, probe, clips and grabbers, green test lead, probe, clips and grabbers, Li-ION battery 4400 mAh, Li-ION battery charge, SIA10 MAINS socket interface adaptor UK, neck strap, multipurpose hard base carry case, quick start guide, calibration certificate.
Our pages are encrypted and protected from cyber-attack.
Payment Card Industry Data Security Standard (PCI DSS) Compliant.
TLS (SSL) - all data/information is secure from interception.
The Megger MFT-X1 multifunction installation tester covers all test requirements, including EV charge points (when paired with the EVCA210 charge-point adaptor) and domestic photovoltaic systems in low-voltage installations.
Megger have redesigned the MFT and this new tester comes with a host of new features and is designed for use on all single or 3-phase domestic, commercial and industrial electrical installations.
Key innovations include True Loop™, Megger’s most advanced earth loop impedance measurement system, user-configurable auto-sequence RCD testing, automatic volt-drop calculation, stabilised IR test voltage output and – an industry first – plug in Li-ION battery module.
The Megger MFT-X1 can be used with either the Megger Li-ION battery pack, or the AA NiMH or Alkaline battery technologies*. The unique battery pack solution enables the rechargeable 4 Ahr Li-ION pack to be swapped with the AA carrier module, providing the most flexible and fastest battery change solution in the industry. A smart fuel tank chip technology optimises battery status accuracy on the Li-ION pack.
* Available after launch
FEATURESCATIV 300 V.
True Loop™ - testing in high noise conditions or close to the source of supply.
High resolution 0.001Ω loop test.
Patented Confidence Meter™ technology.
CertSuite™ Compatibility - fully integrated into the instrument.
RCD configurator - optimise your RCD testing.
Stabilised insulation test voltage - ensuring output voltage is accurate to within +2% +2 digits.
EV Charge Point Testing.
Current measurement using the optional Megger MCC1010 current clamp.
Full colour TFT bonded display.
New Voltage Widget - displays the L-N, L-E and N-E voltages.
Fast switch rechargeable plug-in battery pack.
User upgradeable operating system using a standard microSD card.
Context help with graphical circuit connection guide.
Designed and built in Dover.
|Voltage range||0.001 V to 2 V (mV range) 2 V to 600 V (V range), 1000 V DC (on-CAT rated circuits).|
|Voltage type||Trms, AC, DC.|
|Phase sequence||Automatic phase sequence testing on detection of valid three phase supplies.|
|Current Measurement (non-contact)|
|AC Trms||Using optional accessories: MCC1010 current clamp.|
|Measurement Range||MCC1010: 1 mA to 300 A.|
|Measurement range Digital display||0.01 Ω to 999 kΩ Auto-ranging.|
|Measurement Range Analogue arc||0 Ω to 1 MΩ log scale.|
|Test voltage||4 V DC to 5 V DC.|
|Test current (Nominal)||>200 mA 0 Ω >< 2 Ω
Auto reduction on high resistance (actual current reported in display).
|Test polarities||Forward polarity.|
|Buzzer resistance range||> 0.01 Ω < 2 kΩ.|
|Buzzer threshold||0.3, 0.5, 1, 2, 3, 4, 5, 10, 20, 30, 40, 50, 100, 200 Ω.|
|Measurement range Digital display||0.001 MΩ to 999 MΩ Auto-ranging.|
|Measurement range Analogue arc||0.001 MΩ to >1000 MΩ log scale.|
|Insulation test voltages||50 V DC to 1000 V DC + Variable 50 V to 999 V.|
|Test current||1 mA to 2 mA.|
|Stabilised output voltage||Output test voltage stabilised to -0% +2% +2 V.|
|Loop Impedance Testing|
|2 Wire – all modes|
|Test types||Mode 1: Non-Trip.|
|Mode 2: High current.|
|Mode 3: High resolution.|
|Resolution||Non-Trip: 0.01 Ω.|
|High current: 0.01 Ω.|
|High resolution: 0.001 Ω.|
|Voltage range||Non-trip: 48 V AC to 280 V AC.|
|High current: 48 V AC to 550V AC.|
|High resolution: 48 V AC to 550 V AC.|
|Frequency range||45 Hz to 65 Hz (all modes).|
|Phases||Non-trip: Single phase.|
|High current: Three phase.|
|High resolution: Three phase.|
|3 wire - non-trip|
|Test types||RCD (non-trip)
RCD EV (non-trip on 6mA EV RDCs).
|Voltage range||48 V AC to 280 V.|
|Frequency range||45 Hz to 65 Hz.|
|Volt drop calculation||Requires Zref (Ze) and circuit current (I-vdrop).|
|Accuracy||Dependent on loop impedance accuracy.|
|RCD types supported||Type AC, A, B, AC(S), A(S), B(S).|
|Auto RCD sequence||1/2x I∆n, 1x I∆n, 2x I∆n, 5x I∆n, Ramp, 0º/180º
|Ramp testing||10 mA to 1000 mA.|
|RDC testing||6 mA RDC.|
|Fault (Touch) voltage||0 V to 253 V.|
|2 wire||2 wire earth resistance test.|