All-Test PRO On-Line II

Includes: All-Test Pro On-Line II™, 0.1 - 100A portable current transformer (4), 1 - 6000A flexible, portable current transformer (4), Voltage test leads and clips (4), AC battery charger 115V or 230V (1), Hard sided carrying case (2), ESA & PSM software (1 each), User manual on CD, Warranty card.

HTTPS Secure

Our pages are encrypted and protected from cyber-attack.

Compliant

Payment Card Industry Data Security Standard (PCI DSS) Compliant.

Protected

TLS (SSL) - all data/information is secure from interception.

The ALL-TEST PRO On-Line II Electrical Signature Analysis instrument sets the standard for modern Current and Voltage Signature Analysis and Power Analysis industry-wide.

The system is based on demodulated current and voltage and current Fast-Fourier Transform (FFT) allowing the analyst or technician to view the electrical system both upstream (supply) and downstream (load) from the point of test. The Power Analysis and Electrical Signature Analysis software allows for a complete analysis of the electrical and motor system and is supported with an easy-to-use menu operation and automated data analysis.

Test data can be taken remotely using this hand-held instrument or via the instrument’s Bluetooth wireless interface by using the computer software in virtual instrument mode. Data is uploaded and analysed within minutes, either way

ATPOL II™ is actually two instruments in one - a complete Motor Analyser (ESA) and a complete Power Quality Analyzer (PQ). In ESA mode it evaluates the condition of incoming power, the control circuit, the motor itself, and the driven load and results can be trended for Condition Based Maintenance/Predictive Maintenance purposes. When in PQ mode it can be used for energy data logging, harmonic analysis, voltage and current charting, view waveforms, waveform capture of sags and swells, transient capture and event capture.

For even greater operator safety the optional ALL-SAFE PRO® connection boxes can be installed so the electrical panel need not be opened for data collection purposes. Besides better operator safety during data collection, this will also allow the user to test potentially a hundred motors each day.

FEATURES

Line Frequency, Running Speed and Pole Pass Frequency.
Software automatically looks for patterns related to Stator Slot and Rotor Bar fault frequencies.
Automatic detection of Static or Dynamic eccentricity faults.
Evaluation of Incoming Power, including Harmonics.
Calculates Efficiency for AC Induction & DC Motors.
Power Analysis includes Sag/Swell and Transient Detection plus Energy Consumption Data Logging.

Electrical Signature Analysis Demonstration | ALL TEST PRO On Line II

ALL-TEST Pro On-line II Specifications

Voltage: 1-1000 Vrms steady state using the 1-6000A Flex CT
Display range	1-6 megavolt (using input ratios).
Accuracy	0.1% of reading over input range +/- 0.3 Vrms.
Repetition rate	Measure every cycle of every input.
Frequency response	No de-rating of accuracy for harmonics through 3900 Hz.
Current
Measuring range	0.005 – 6000 Amps, AC or DC with proper CT attached.
Display range	1mA – 6 Megamps (using input ratios).
Accuracy	.1% plus accuracy of current probe.
Repetition rate	Measure every cycle of every input.
Frequency response	Dependent on current probe attached.
Frequency
0.25% accuracy	DC, 22 – 200 Hz, 360 – 440 Hz fundamental frequency. DC and 22-3900 Hz included in RMS 22-3900 Hz for harmonic measurements.
Power
Harmonic Distortion	Out to 65th range; 1% resolution of fundamental.
Power, Energy, Cost, Power Factor	1 Watt to 999MW display range; 0.5% accuracy plus accuracy of CT.
Swell/Dip Detection	RMS measured every half cycle of every input.
High Speed Transient Detection	Measured every 8 μSec on every input.
Quantity of Captured Waveforms	set by user allocation of memory.
General Specifications
Memory	SD Memory Card Slot for SD cards up to 32 GByte.
Temperature range	32°- 122° F (0° – 50° C) and relative humidity to 70%.
Protection	IP40 per IEC 529.
Power	12 VDC @ 500mA, wall mount power supply included.
Battery life	Internal Li-ion operates 8 hours after 4 hours charge.
Safety	CE for a 1000V Category III, pollution degree II, Double Insulated.
Dimensions	3.88” x 7.72” x 2.14” (9.86cm x 19.61cm x 5.44cm).
Weight	1.1 lb (0.50 kg).
ALL-TEST Pro On-line II warranty	1 year limited warranty. Optional 2 years available with calibration.

Brand ALL-TEST Pro

Reference 50074

Download

All-Test ATPOL II Datasheet

PDF Brochure of the All-Test Pro On-line II energised motor tester.

Download (850.79k)